LENGTH:  2"
WIDTH:  1/8"

FITS TORO/WHEL HORSE 21" SELF PROPELLED WALK BEHIND.  
USED ON SHORT SHAFT IN GEAR CASE.

FITS LAWN-BOY "F" ENGINES SELF-PROPELLED.

Can use part# 3220737 Fits model UT13118

Replaces Snapper 1-0121, 7010121, 7010121YP
Fits our Snapper R6880 Drive Disc Assembly.
ID: 3/4"
OD: 1"

Replaces Briggs 692191, 91539

FITS BRIGGS & STRATTON MODELS 2 THRU 18HP.

LENGTH:  1-1/2"
WIDTH:  3/16"

Replaces OEM: SNAPPER: 1-1024, 7011024, 7011024YP
OIL FILL & CHECK PLUG.

Replaces SNAPPER/KEES 1-2617, 7012617, 7012617YP
FLANGE OD: 1-1/4"
HEIGHT: 5/8"
ID: 29/32"
OD: 31/32"
NYLON BUSHING

611298 Key

Replaces; MTD 741-0225, 941-0225
King pin bushing fits 38" and 42" cut front engine riders.
HEIGHT:  5/8"
ID:  5/8"
OD:  7/8"

ID:  1-1/16"
OD:  1-13/16"
REAR AXLE OIL SEAL FOR SNAPPER REAR ENGINE RIDERS.

Replaces MTD 741-0374
ITS MTD MODEL 406 REAR TINE TILLER.
LOWER CHAIN CASE BEARING ON TILLER
FLANGED OD: 1-1/2"
HEIGHT: 19/32"
ID: 1"
OD: 1-1/4"

Replaces MTD 731-0393, 931-0393
ID:  1/2"
OD:  2-1/4"
WIDTH:  1-7/8"

CONTROL ROD LINKAGE SWIVEL FITS BOBCAT.  
5/16"

ID:  11/16"
OD:  1-27/32"
LEFT REAR WHEEL OIL SEAL ON SNAPPER 25", 26", 28", 30" & 33" CUT REAR ENGINE RIDERS.

Replaces Snapper 1-2296, 7012296, 7012296YP
Right side rear axle bearing fits Snapper 12296. for 26" thru 33" Rear Engine Riders.
FLANGE: 1/4"
HEIGHT: 1-1/2"
ID: 1-1/8"
OD: 1-5/8"

Replaces NLA 20066MA
ID: 5/8" OD: 2-3/4" WIDTH: 1-7/8"

Replaces AYP, Husqvarna 106888X, 532106888

Replaces Snapper 1-8060, 2-8762, 7028762

532071673

REPLACES TECUMSEH 799021/790006.
USED ON AMF, SIMPLICITY.
FITS PEERLESS 600 SERIES TRANSAXLES.
LENGTH: 1-1/8"
WIDTH: 1/2"
THICKNESS: 1/4"

Replaces Snapper 57423
NON-ASBESTOS Lining only

Replaces 33308371, 3330837-1, R8440517004, 8440517004

Replaces Briggs & Stratton 91540

ID:  5/8"
OD:  3-1/8"
WIDTH:  2-5/16"

DRIVE GEAR FITS TORO/WHEEL HORSE MODELS:  22020, 22030, 22035 & 20680 REAR WHEEL DRIVE MODELS.

Replaces MTD 717-0678

Fits Homelite UT13118 18" Inch Corded Electric Mower

Replaces Homelite 3330437-1
Fits Homelite electric mower models:
UT13122 20" Inch Cordless Electric Mower
UT13118 18" Inch Corded Electric Mower
UT13120 20" Inch Corded Electric Mower

Replaces MTD 746-0970, 946-0970
LENGTH:  5-3/4"

FITS 42" DECK MOWERS. 3/8" EYELETS ON EACH END.

CHAIN TYPE:  #43
HEIGHT:  3/4"
ID:  1/2"
NO. OF TEETH:  10
OD:  1"

REPLACES OEM#: SNAPPER 12605, 7012605
For Snapper 33" rear engine riders.
Length 55"
(Black)

Replaces MTD 746-0946, 946-0946
CONDUIT LENGTH:  48-1/4"
TOTAL LENGTH:  60-1/4"
WIRE LENGTH:  12-1/2"

FITS MOST MTD SIDE DISCHARGE MOWERS 1986 & PRIOR.
SNAP TO FIT HANDLE.

Replaces MTD 746-0551, 946-0551
CONDUIT LENGTH:  43"
TOTAL LENGTH:  49-1/2"
WIRE LENGTH:  5-1/2"

FITS MODEL 440, E466 AND 469 SERIES.

Replaces MTD 746-0553, 946-0553
CONDUIT LENGTH:  36-7/8"
LENGTH:  43-1/8"

FITS MTD 1991 & NEWER PUSH MOWERS WITH B&S ENGINES. MODELS 030-042, 030-042, 030-418.    
Z-BEND ON EACH END

LENGTH:  50"
FITS SNAPPER REAR ENGINE RIDERS WITH 33" & 41" DECKS & ONE BRAKE/CLUTCH PEDAL.

Replaces Snapper 6-0278, 7060278, 7060278YP
Fits 26" thru 33" cut riding mowers.
Kits includes our R6864 rear axle bearing, R3453 clamp, R7919 seal cap & R8632 oil seal.

CONDUIT LENGTH:  55"
TOTAL LENGTH:  61-1/2"
WIRE LENGTH:  5-1/2"

Replaces MTD 746-0555, 946-0555
FOR MODEL 573, 20" DECK, MODEL 370 - 379.
MODEL 445 21" REAR-DISCHARGE.
DIE CAST "Z" BEND ON EACH END.

Replaces MTD 746-0737, 946-0737
CONDUIT LENGTH:  51"
TOTAL LENGTH:  55-1/2"
WIRE LENGTH:  5-1/2"

FOR 1994 - 97 WALK-BEHIND MODEL SERIES 070, 080, 100, 200, 400 & 500.
DIE CAST "Z" BENDS ON EACH END.

Replaces Honda 54510-VG4-C01
Fits Homda models HRRK216K, HRT216K & HRZ216
Conduit Length: 49"
Total Length: 57-1/2"

LENGTH:  42-1/2"

Replaces Honda 54520-VA3-801  
Fits Honda model HR214 walk behind mower.
Conduit length 42-1/8"
Inner wire 44-3/4"
Wire travel 1-1/2"

Replaces Snapper 7034604, 7034604YP
Fits 21" Self Propelled.
Cable length 42"

Replaces Honda 54530-VE0-003
FITS MODELS HRB215XA, HRB215K15XR,HRB215K2HXA.
CONDUIT:  45"
INNER WIRE:  54-3/4"
WIRE TRAVEL:  9-1/4"

Replaces Snapper 7050918, 7050918YP
Left side rear axle bushing with grease fitting for 26" thru 33" Rear Engine Riders.
BOTTOM OD: 1-5/8"
ID: 3/4"
OVERALL HEIGHT: 1-3/4"
TOP HEIGHT: 1"
TOP OD: 1-3/4"

Replaces MTD  746-1113, 946-1113
CONDUIT LENGTH:  37-3/8"
TOTAL LENGTH:  51"
WIRE TRAVEL:  12"

Replaces AYP 156581, 168552, 156577
CONDUIT LENGTH:  54"
INNER WIRE LENGTH:  60"
WIRE TRAVEL:  6"

Replaces MTD 746-0552, 946-0552
CONDUIT LENGTH:  49"
TOTAL LENGTH:  53-1/2"
WIRE LENGTH:  5-1/2"

FITS 1985 & UP WALK-BEHIND MODEL SERIES 030, 040, 050, 060, 070, 080, 090, 100, 200, 400 & 700.
FOR SELF-PROPELLED MODEL SERIES 200, 400 * 700.
PUSH IN CLIP WITH HEAVY "Z" BEND ON EACH END.

Replaces Honda 54530-VB3-802
FITS MODELS HR214SXA, HRA214SXA.
CONDUIT:  53"
INNER WIRE:  65-1/2"
WIRE TRAVEL:  10"

Replaces MTD 946-04206A
Fits walk behind mowers
Conduit Length 76"
Inner Wire 79-1/2"
Wire Travel 3-1/4"

Replaces OEM#: Toro 103-2683
Fits Heavy Duty Recycler Models 22162-22190
CONDUIT LENGTH: 62"
TOTAL LENGTH: 67-1/2"
WIRE TRAVEL: 4-1/2"

Replaces 1102005
Fits Murray 224110x8D Walk-Behind Mower

Replaces Snapper 7101418, Replaces John Deere GY21068

Replaces Murray 672831

Replaces Snapper 53103, 57423, 7053103, 7600135
Contains our R300 disc & R345 liner.

OD 4"

Replaces OEM#: Cub Cadet 746-04066
Fits Cub Cadet RZT 50/54 & GT1222
CONDUIT:  34"
INNER WIRE:  36-1/4"
WIRE TRAVEL:  1-1/2"

Replaces 1101362

Replaces (OEM): Ariens: 02201300, 03240700, 03248300
John Deere: AM123355, M110594
Murray: 1501435, 1501435MA
Noma: 1501435, 313883, 53830, 9005383
Stiga: 1812-9002-01
Fits ARIENS 922003, 922006-922010, 922012-922022 Snowblowers.
Fits JOHN DEERE 524D, 724D and 826D Snowblowers
Fits many Murray & Craftsman Snowblowers
Fits NOMA 21" SELF PROPELLED MOWERS
ID: 2-1/4"
OD: 4-7/16"

Replaces Murray 1101365
Length: 58.00
Fits Murray Model 22 Series (2001-2005)

LENGTH:  67-1/2"
FITS 61" & 72" CUT SCAG RIDERS MODELS; ST17KA & 19KH.

Replaces PEERLESS 771842, Scag 481582, MTD Pro / Cub Cadet Commercial 00030352 & Wright 39490002.
Pro-Gear Drive Shaft 30-1017. 6-1/4" long 9-Spline.

Replaces Toro 78-2900-01, 28-2900, 782900, 78290001
Length: 9 5/8" OVERALL Thread Size: 3/8" -24 UNF X 7/8" L STUD
For right and left side Made by an OEM supplier

USED ON SNAPPER SELF-PROPELLED MOWERS.

Replaces 792089A

1725428SM Genuine Simplicity Friction Disc

* This part replaces: 746-04609, 946-04609

Replaces Murray 1101670
Fits Murray 22 Series (2003-2005)