Use on all 14 mm spark plugs
Length: 3"
Zinc plated, pointed to penetrate plug boot

(Used only with Breaker Point Ignition)

Replacement 3/4" rubber cup for R9050.

Superseded by part number 670263

Starter Rope 99" cut to required length. Superseded by 692188

1/2" x 6" Shrink Tube

3/4" x 6" Shrink Tube

1/8" x 6" Shrink Tube

3/16" x 6" Shrink Tube

1/4" x 6" Shrink Tube

3/8" x 6" Shrink Tube

6" knot type wire wheel. 1/2" ID.

REPLACEMENT PIN FOR R1733.

Fits any 1/4" or 3/8" electric drill. With nylon guide. Sharpens lawnmower blades, roto tillers, sickle bar cutters, hoes and scythes

Locks piston in 2 cycle engines to help removal of clutches and flywheels
14mm thread machined steel

3MM T-Handle Allen Style Hex Wrench

4MM T-Handle Allen Style Hex Wrench

5MM T-Handle Wrench

T-Handle Torx  Wrench 20-T27

280399 Genuine Briggs & Stratton Starter Rope 99" cut to required length.

Suction Cup Style with 15/16" and 1-1/16" diameter cups.
Fits all small engines.

Made of zinc die cast G30.

Compressor - Fits most fractional horse-power engines. Notched end compresses valve spring. Hook end aligns valve spring retainer. Remove and install valve springs on all engines using self-locking valve spring retainers.

Easily and safely removes flywheel

NEW OLD STOCK

Sold in Packages of 10

Sold in Packages of 10

Sold in Packages of 10

Sold in Packages of 10

Sold in Packages of 10

Sold in Packages of 10

Sold in Packages of 10

Discontinued New-Old Stock

Discontinued New-Old Stock

Works with our R9036 Compression Tester

Sold in Packages of 10

Discontinued New-Old Stock

Discontinued New-Old Stock

Genuine Briggs & Stratton Puller Washer

Discontinued New-Old Stock

Replaces OEM: FOLEY/PLP: 186-032
Internal - Stens: 750109
TECUMSEH: 670103
For Tecumseh 3.5 HP engines
7/16" THD

Sold in Packages of 10

5/16" For L-Head Engines 5 HP And Over
Sintered Guide Gray or Copper Colored

Discontinued New-Old stock

Discontinued New-Old Stock

Discontinued New-Old Stock

Genuine Briggs & Stratton Bushing Driver-Plunger

Discontinued New-Old Stock

Universal-Mounts easily with 2 nuts provided.
Diameter: 2-1/4"

Sold in Packages of 10

Sold in Packages of 10

Sold in Packages of 10

Sold in Packages of 10

For cylinders with 1-1/2" to 3" diameter.
Made of blued spring steel.

Sold in Packages of 10

Sold in Packages of 10

Replacement Stones for R1704 Cylinder Hone. 2" Length x 5/16". Set of Three. (medium grit)

Great for helping snowblower users remove slush and snow from the discharge chute area.
A great safety device, keeping your hands away from danger while they stay warm and dry.
Convenience and Safety all in one!

Sold in Packages of 10

Sold in Packages of 10

Allows visual inspection of ignition output.
Use between coil wire and spark plug

Discontinued New-Old Stock

Lightweight - For use with Chain 35, 40, 41, 42, 43 or 50. Fast and simple method of taking apart rivet type roller chain.

A multifunctional tool that allows the technician to perform many tasks on the carburetor during cleaning.
Installs Seats
Removes Emulsion Tube
Removes Seats
Removes O-Rings
Pilot Seats
Sets Float Height

Genuine Briggs & Stratton Large Flywheel Puller
Fits larger L-head and most OHV engines

Genuine Briggs & Stratton Clutch Wrench
Removes & Installs rewind starter clutches

#250 Blades for previous model 102A. One blade per pack

#251 Blades for model 102A. One blade per pack.

For installing and removing piston rings without the danger of breakage or distortion.
No adjustments needed. All rings expanded whether step-cut or diagonal cut.

Sold in Packages of 10

Replacement feet for R9033.
Suggested Retail: $18.99

Genuine Briggs & Stratton Medium Flywheel Puller
Fits the 7hp / 8hp L-head engines, early 11hp

For #35 thru #60 Chain.
Tool to help put a chain on at the right tension.
Leaves both hands free to connect the chain.

This one of a kind tool is the complete versatile tool for lapping and grinding valves in seats.
Has short locking stems and valve head insert end for both.
Also comes equipped with spring and vacuum cup for lapping.
Inexpensive but extremely valuable to small engine mechanics.

The ideal tool for removing and replacing valve springs of B&S engines.
Long and slender, it is adapted to reach into small recesses in which valve springs and retaining washers are located.
The arms are hinged so they are practically parallel at the jaws.
Spring steel jaws are adjustable in width to fit the valve springs and have edges so thin that they can be easily forced under and over the ends of the valve spring to compress it for removal.
Finished in Cadmium.

Adjustable Ignition Spark Tester works on Ignition Systems from
High Energy Electronic Automative Systems to Small Engines.
Tests for no start conditions and for Spark Strength.
Adjustable gap allows for different Spark Gap requirements
of different systems from 0 to 40,000 Volts.
Gauge background makes spark easy to see for accurate measurement.
Alligator Clip securely fastens to ground.

670366 Genuine Tecumseh spark tester

Genuine Briggs & Stratton Reamer-Valve Guide

Installs new primer bulb and retainer in a "snap".

Fix-A-Thread Repair Kit

Used to test all ignition coil except Vanguard 3 L/C gas engines.
For the Vanguard 3 L/C gas engines, please see 19400 Spark Tester

Fix-A-Thread Repair Kit

Fix-A-Thread Repair Kit

5 Quart (4.73L) Oil Extractor
Easy to Use, No power or batteries required
Long hoses to siphon fluid
Strain relief external pump handle
Translucent Tank
Tubes for either internal or external dipstick
(48" each)
Vacuum relief valve to stop the flow of fluid
Can extract 5 quarts of fluid in 5 to 10
minutes (depending on the number of pumps).

Fix-A-Thread Repair Kit

Fix-A-Thread Repair Kit

Genuine Briggs & Stratton Maintenance Meter
Used for 2 and 4 cycle engines.

Display flashes every 25 hours run time.
Displays up to 999 hours of run time and is resetable.