R12492 Sealant/Adhesive HV-350 3.35 oz. Tube
Valco HV-350 Sealant/Adhesive. 3.35 oz. HV-350 is a one-part, multi-purpose adhesive that virtually out performs any glue, epoxy or silicone on the market. The "HV" stands for high vibration. Due to its tremendous elasticity, HV-350 is ideal for high-vibration applications. HV-350 can be stretched up to 600 percent of its original length. Maximum temperature is 230 degrees Fahrenheit. Use HV-350 to adhere mats, repair fiberglass, mend rips in wet suits, waterproof electrical components, attach plastic and carbon fiber parts and much more. Unlike silicone, HV-350 can be sanded and then painted with either oil-based or water-based paints. It is also abrasive-resistant and flexible, allowing use on high-wear surfaces. This glue is used almost anywhere, from highly porous surfaces such as cinder blocks to nonporous surfaces such as metal and glass.
This item must be picked up in our store.
R12223 Sea Foam Motor Treatment for Gas & Diesel Engines
INSTANT ACTION
SEA FOAM MOTOR TREATMENT
100% Pure Petroleum
Use in All Engines in All Seasons
2 Cycle, 4 Cycle, and Diesels
Treats 3 Critical Areas: Gas Tank, Fuel Systems, and Crankcase
Cleans fuel injectors
Cleans carburetor jets
Cleans carbon
Stabilizes fuels
Upper cylinder lube
Removes moisture in fuel
De-icer
Frees sticky lifters
Frees sticky rings
Removes moisture in oil
Cleans P.C.V. systems
Cleans catalytic converter odors
Oxygen sensor safe
For Peak Performance, Use SEA FOAM Every 2,000 to 5,000 Miles
A 100% pure petroleum product for use in all gasoline and diesel type engines, both 2 and 4 cycle. OXYGEN SENSOR SAFE.
Cleans dirty engine parts internally by removing harmful gums, varnish and carbon. WORKS AND PERFORMS INSTANTLY.
Removes moisture from oil crankcases and fuel tanks.
Stabilizes and conditions fuels. Use for engine storage.
Cure hesitations, stalls, pings and rough idle due to carbon buildup.
Helps pass emissions test. EPA Registered.
When Used Thru Injection or Carburetor
Cleans carbon build up
Cleans intake valves and pistons
Gives smoother idle
Cleans catalytic converter odors
Cures hesitations and pings
Restores power and pickup
With warm engine running, SLOWLY poor 1/2 pint through carburator, throttle body or direct manifold vacuum line that will feed ALL CYLINDERS. Possible sources are P.C.V. valve or brake booster line. Turn ignition off. Restart engine after 5 minutes. Be sure exhaust is well ventilated. Fumes will be extreme for a short period of time.
For use in injector cleaning machines, use 50% SEA FOAM and 50% fuel.
Fill diesel filters with SEA FOAM to clean injectors fast.
When Added to Crankcase (Oil)
Frees sticky lifters and rings
Increases R.P.M.'s vacuum and compression
Cleans dirty parts
Removes moisture
Cleans PCV valve systems
One pint treats 10 quarts of oil (avg. 1 1/2 ounce per quart).
When Added to Fuel Tank
Cleans fuel injectors and carburetor jets
Cleans carbon as you drive
Lubricates upper cylinders
De-ices and removes moisture
Diesel full conditioner and anti gel
Stabilizes fuel
One pint treats 8-25 gallons of fuel (average 1 ounce per gallon).
In Injector Cleaning Machines
Add a 50/50 blend of fuel and SEA FOAM into injector cleaning machine. Run directly through the fuel rails to clean injectors fast. Add SEA FOAM to your fuel tank to clean injectors as you drive
This item must be picked up in our store.
R12460 Start Your Engines Fuel System Revitalizer
For quick, reliable starts of power equipment right out of storage and during season.
Helps remove gum and varnish from throttle plate and carburetor.
Smoothes out rough idling and eliminates warm engine stalling.
Removes water and dries the entire fuel system.
Prevents rust and corrosion.
Safe to use in all 2 and 4 cycle engines.
Use in gasoline, gas/oil mixtures, ethanol blends.
Cleans fuel injectors, carburetors and intake valves.
This item must be picked up in our store.
